5kV Non-Shielded Splice Kits. MVSN 50, MVSTN 50, MVS3N 50, MVSA3N 50,
1/C, 3/C to 3-1/C, 3/C armored, 2.3 - 6.6kV splices for extruded dielectric non-shielded cables


The Innovative Power Products MVSN 50 series splices are heatshrinkable kits for splicing 5kV (2.3-6.6kV), extruded dielectric, non-shielded, medium voltage power cables. MVSN 50 series kits provide a lightweight, compact and environmentally sealed system for splicing extruded dielectric, non-shielded power cable. These splices can be installed in duct systems, vaults, submersible or direct-buried applications. MVSN 50 series splice system provides a total environmental seal. Splice failures in flooded vaults are eliminated.



  • The kits are packaged to provide three (3) single-core splices for MVSN 50 splices, or one (1) three-core cable splice for MVSTN 50, MVS3N 50 and MVSA3N 50 splice kits. These factory engineered kits are supplied with everything that is necessary to rebuild the cable, less the butt-splice connectors. Connectors can be supplied in the kits; subject to factory quote. See section 5 for connector information.


  • MVSN 50 kits are factory engineered to provide fast, easy and repeatable installations with reliable performance. These splices meet the applicable sections of ICEA power cable standards relative to non-shielded 5kV cables.


  • To download a PDF copy of the data sheet Click here.

    For a complete PDF of the current IPP catalog Click Here. If you would like the catalog in a printed version, please go to the "Catalog Request" page via the link at the top of the page.


  • MVSN 50 series splice kits use field control material over the connector to suppress partial discharge. A corona resistant heavy walled sleeve is then installed over the connector for insulation. Sealant is applied at both ends of the insulating sleeve to make the primary seal, and a heavy-walled insulating/ jacketing sleeve is shrunk in place to complete the splice.


1/C to 1/C, 5 kV Nonshielded Straight Splice Kit


Kit Contents:
The MVSN 50 series splice kits contain the following:
 
- Field control material
   
- Corona resistant insulating sleeve
   
- Sealant strips
   
- Insulating/Jacketing sleeve
   
- Installation Guide
   
     
Selection Guide
1/C Conductor Range Catalog # Jacket O.D. Min Range max.
2/0 AWG
MVSN 51
0.42 0.85
3/0 - 350 kcmil
MVSN 52
0.75 1.25
400 - 1250 kmil
MVSN 53
1.16 2.05
       



  • MVSTN 50 series splice kits use the single-core MVSN 50 series splices plus additional components to convert the three-core cable into three, single-core cables. The small diameter tubings are for jacketing the ground wires, and the cable breakout and sealing profile seal the three cores and ground wires. The single-core MVSN 50 series splices are then installed in the normal manner.


3/C to 3-1/C, 5 kV Non-shielded Trifurcating Splice Kit


Kit Contents:
The MVSTN 50 series splice kits contain the following:
 
- MVSN 50 series splice kitsl
   
- Ground wire jacketing tubes
   
- Sealing profile
   
- Three-legged cable breakout
   
- Installation Guide
   
     
Selection Guide
3/C Conductor Range Catalog # Jacket O.D. Min Range max.
6 - 2/0 AWG
MVSTN 51
1.00 2.00
3/0 - 350 kcmil
MVSTN 52
1.45 2.85
400 - 1000 kcmil
MVSTN 53
1.70 3.75
       



  • The MVS3N 50 series splice kits use the single-core MVSN 50 series splices plus an additional heatshrinkable tubular tubing. The single-core splices are installed normally, then the outer tubular tubing is installed to rejacket the spliced three-core cable.


3/C to 3/C, 5 kV Non-shielded Straight Splice Kit


Kit Contents:
The MVS3N 50 series splice kits contain the following:
 
- MVSN 50 series splice kits
   
- Wraparound heatshrinkable outer sleeve ***
   
- Installation Guide
   
     
Selection Guide
3/C Conductor Range
Catalog # Jacket O.D. Min Range max.
6 - 2/0 AWG
MVS3N 51
1.00 2.00
3/0 - 350 kcmil
MVS3N 52
1.45 2.85
400 - 1000 kcmil
MVS3N 53
1.70 3.75
       



  • The MVSA3N 50 series splice kits are designed using the single-core MVSN 50 series splices plus an additional wraparound armor case and heatshrinkable tubular tubing. The single core splices are installed normally. The wraparound armor case and outer tubular tubing sleeve are installed to seal and protect the spliced armored cable.


3/C to 3/C, 5 kV Armored Non-shielded Splice Kit


Kit Contents:
The MVSA3N 50 series splice kits contain the following:
 
- MVSN 50 series splice kits
   
- Wraparound armor case
   
- Wraparound heatshrinkable outer sleeve ***
   
- Installation Guide
   
     
Selection Guide
3/C Conductor Range
Catalog # Jacket O.D. Min Range max.
6 - 2/0 AWG
MVSA3N 51
1.00 2.00
3/0 - 350 kcmil
MVSA3N 52
1.45 2.85
400 - 1000 kcmil
MVSA3N 53
1.70 3.75
       



  • All MVSN 50 Series Products: Price List PL-602

QUESTIONS OR QUOTES EMAIL US AT: sales@ippcorp.com or CALL TOLL FREE 1-800-544-4626